欢迎来到 糖果派对连环夺宝平台网站
全国咨询热线: 180-0275-8998
推荐产品
联系我们

地址:广东省东莞市长安镇上沙工业区

电话:180-0275-8998

传真:(86)0759-81889506

邮箱:dgzhangyi1688@163.com

KNP绕线电阻规格书-彰亿电子绕线电阻供应商
时间: 2018-10-31浏览次数:
东莞市彰亿电子-绕线电阻规格书KNP 1. 適用範圍 Applicable Scope 此基準是供應家電,電腦,資訊用之不燃性塗裝型繞線電阻器之規格。 Applicable Scope: This KNP type standard specification is for use in c

东莞市彰亿电子-绕线电阻规格书KNP

1.適用範圍Applicable Scope
此基準是供應家電,電腦,資訊用之不燃性塗裝型繞線電阻器之規格。
Applicable Scope: This KNP type standard specification is for use in consumer electronics
computer, telecommunication equipments﹍﹍etc
 
2.形名  Part Number
 依據其種類、額定電力、端子型狀、特性、公稱電阻及容許誤差等分別注明。
 It is composed by Type, Rated Wattage, Terminal Form, Characteristic, and Nominal Resistance
  and Tolerance.e.g.
 

KNP 10W P(M.F) T-2(±350PPM/℃) Ω J(±5%)
種類 額定電力 端子形狀 特性 公稱電阻值 容差
Type Rate Wattage Terminal Form Characteristic Nominal Resistance Tolerance
 
 
 
 
 
 
2-1.種類 Type
不燃性塗裝型繞線有感電阻器以KNP表示之。
Wire Wound Resistor is called “KNP”
2-2.額定電力  Rated Wattage
    額定電力(W)以數字表示,如1/2W、1W、2W、﹍﹍40W。
     Shown by “W”﹑such as 1/2W 、1W、2W、﹍﹍40W。
2-3.端子形狀Terminal Form
視端子區分為P形、M形、F形。
Upon the shape of terminal, it has P Form and M form , F form
2-4.特性  Characteristic
     溫度系數以“T”表示之,如:
     Temperature Coefficient is its character represented by “T”, such as:
     ±350PPM/℃
2-5.公稱電阻值Nominal Resistance:
      Ω,KΩ為單位,依據JIS-C6402為適用原則(E-24 Series)。
      Ω,KΩ are its unit which is in accordance with JIS-C6402(E-24)series.
2-6.電阻值及容許誤差 Tolerance
      在室溫中依檢測器測量,應在指定電阻值之容許誤差以內。
      It is measured by Bridge-method at room temperature and expressed by a capital letter.
           F ± 1%    G ±2%    J ±5%    K ±10%
2-7.使用CN-49W   ψ0.32㎜線材
 
3,額定功率Rated power
 
  額定電力是周圍溫度70℃以下可連續使用之負載電力最大值數,且應使機械性能與電氣性能滿
  足。又周圍溫度超越上記溫度時,依造圖一之電力輕減曲線而定。
  Rated power is the value of Max load voltage specified at the ambient temperature of 70℃ and shall
  meet the functions of electrical and mechanical performance. When the ambient temp.surpasses above
  
 Mentioned temperature. The value declines as following
  DERATING CURVE:
 



3-1.額定電壓  Rated Voltage
     依公式E=√PR求出連續使用額定電壓,如額定電壓超出最高使用電壓,
     則以最高使用電壓為連續使用額定電壓
 It is calculated as the following formula E=√PR
    However, in case the voltage calculated exceeds the maximum load voltage, such the maximum load.
    Voltage shall be regarded as its rated voltage, means whichever less.
 E=連續使用額定電壓      E=Rated Continuous Working Voltage(V)
     P=額定功率              P=Rated Power(W)
     R=公稱電阻值            R=Nominal Resistance Value(Ω)
3-2備注
1.  K N P阻抗範圍0.01Ω-1KΩ(N K N P則為0.01Ω-100Ω).
2.  無感繞線電阻(N K N P)的特性說明:
 
本項產品可減少各种電子回路的雜訊或瞬間突破,如用在交換式電源供應器或不斷電設備之電
流感應器(Current Sensory)或突破吸收部分(Snubbed)時, 可將雜訊干擾降至最低限度,提高振頻率或縮小前產品的體積,節省材料費用,並可防止振蕩,且突破降低自然可減少電磁波之干擾。
 
 
4.       CONSTRUCTOION
                                                            
                                                 

a. 高熱傳導瓷心  CERAMIC CORE (HIGH CONDUCTIVITY)
b. 不燃性絕緣塗漆  (NONFLAME PAINT WITH SOL VENT-PROOF)
c. 壓合度良好之高信賴性端帽  END CAP(HIGH RELIABILITY FITTING BY ORIGINAL
                            CAP-PRESSING METHOD)
d. 高穩定性鎳鉻合金線原材料  COPPER-NICKEL ALLOY WIRE WOUND FILM(HIGH STABILITY)
e. 符全MIT﹠EIA規定之標準色碼帶  COLOR CODE(PER MIL&ELA STAND ARDS PERMANENT)
f. 鍍錫導線   LEAD   WIRE
 
5.定格及尺寸  SPECIFICATIONS
                                                  
 
 
額定電力
POWER
RATING
DIMENSION(㎜) 阻值範圍
RESISTANCE
RANGE
L D H d ±0.1 DIELECTRIC
WITHSTANDING 
1/2W/1WS 9.0 ±0.5 3.2 ±0.5 26 ±2.0 0.5 300 0.01Ω-100Ω
1W/2WS 11.5 ±1.0 4.2 ±0.5 25 ±1.0 0.65 350 0.01Ω-360Ω
2W/3WS 15.5 ±1.0 5.0 ±0.5 28 ±1.0 0.68 500 0.01Ω-470Ω
3W/5WS 17.0 ±1.0 6.5 ±0.5 32 ±1.0 0.68 500 0.01Ω-1KΩ
5W/7WS 24.0 ±1.0 8.5 ±0.5 28 ±3.0 0.68 700 0.01Ω-1KΩ
10W 53.0 ±1.0 8.5 ±1.0 38±1.0 0.73 700 0.01Ω-1KΩ
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
          
 
 
 
 
 
 6.機械性能  Mechanical Performance
6-1.端子彎曲強度   Terminal Bend
一手持電阻體,另一手將端子彎曲90°後,恢復原位,繼續再向反方向彎曲90°,如此三次
而接頭不可脫落或折斷。
The terminal shall withstand 4 bends of 90°rotation without any breakage or damage, when the
Resistor is fixed in vertical position.
 6-2.端子拉力強度  Terminal Tensile
將電阻本體一端固定,另一端向電阻體軸方向,慢慢加重至2.5Kg後,保持10秒鐘,本體不得
脫落或鬆動。
Fixing the resistor body, a static load of 2.5Kg is to be gradually applied into the terminal for
10seconds without causing any looseness and fall.
   6-3.扭轉強度  Twist Withstand
自電阻體起約6mm處之端子線,以約0.8mm曲率半經彎曲90°,其次由彎曲處向端子線先
端1.2±0.4mm處挾定端子引出軸,為回轉軸,以約5秒時間沿面回軸360°再逆轉360°,如
此施行回逆轉2次,不可發生折斷及鬆動現象。
To bend the lead wire at the point of about 6mm from resistor body to 90°,then catch the
wire at 1.2±0.4mm apart from the bend point end and turn it (clockwise) by 360 degrees
Perpendicular to the resistor axis at speed of sane 5 seconds per turn, and do the same
Counterclockwise again which constitute a whole turn. Repeat the turn for 2 times without
Causing any break and looseness.
 
7.使用溫度:Operating Temperature Range
  -50℃~275℃以內
 
 
8.電氣特性  ELECTRICAL PERFORMANCE
項目ITEM 規格值SPECIFICATIONS 試驗方法TEST METHODS (JIS C5202)
抵抗值
DC RESISTANCE
須在規定之R值的容許差內
ALLOWED UNDER R RATE
TOLERANCE
 
短時間過負載
SHORT TIME
OVER LOAD
 
±(2%+0.05Ω)以內
±(2%+0.05Ω)LESS THAN
5.5定格電壓*3.16倍 測試5秒
PERMANENT RESISTANCE CHANGE
AFTER THE APPLICATION OF A
POTENTIAL OF 2.5 TIME RCWV
FOR 5 SECONDS
耐電壓
DIELECTRIC
WITHSTANDING
VOLTAGE
塗裝不可損壞, 絕緣不可破壞
NO EVIDENCE OF
 FLASHOO-VER MECHANICAL DAMAGE
ARCTIN OR INSULATION
BREAKDOWN
5.7電阻兩端導線置於V型,槽上依特性
表之電壓規定加壓60秒
RESISTORS SHALL BE CLAMPED
IN V-BLOCK AND SHALL BE
TEST AT SPECIFIED IN THE
ABOVE LIST ROR 60 SECONDS
焊錫附著性
ADHESION OF
SOLDERABILITY
端子表面積3/4以新焊錫所
覆蓋為原則
3/4 SURFACE OF TERMINAL
COVERED BY SOLDER
6.5  235 ±5℃    3 ±0.5秒  (sec)
 
 
 9. 色碼表示Color Coding




小型化塗粉紅色或塗綠色
 
10. 注意事項  REQUIRENTS IN USE
1. 濕氣會使電極之焊錫劣質化,保持場所在溫度40℃ 以下濕度 70%以下。
   IN THE HIGH HUMIDITY SITUATION, IT WILL  MAKE THE SOLDER ABILITY
   WORST. PLEASE PRESERVE THE RESISTORS IN 40℃ ,70 RH BELOW
 2. 儘量不要打開最小包裝。
   PLEASE DON`T OPEN THE MINE PACKAGE WHEN YOU PRESERVE IT
 3. 周圍溫度高時按照負荷減輕曲線圖減少使規定用電力。
   WHEN IN THE HIGH TEMPERATURE SITUATION, PLEASE ACCORD TO THE
   PICTURE OF “POWER DERATING CURVE” REDUCE THE USE OF POWER RATING
4. 儘量不要將多個電阻並列或直列連結, 而以大電壓或大電流使用。
   YOU SHOULD AVOID THE CONNECTOR OF RESISATNCE REPLACED BY LATGE
   VOLTAGE AND POWER
5. 由於特殊塗料之故, 對外部衝極力較弱, 故注意各種處置。
   DUE TO ITS SPECIAT MATERIAL OF PAINT, YOU MUST BE CAREFUL TO
   TIS WEAK APPEARANCE
6. 洗淨後, 外膜多少會弱化, 然後自然放置後可復元其強度所以洗淨後20分鐘內不要任電阻皮
膜有任何品之接觸。
   AFTER CLEANING THE BODY, IT WILL MAKE THE FILM WEAKER. BUT IF YOU LET IT NATURE DRY WITHOUT TOUCHING OR PAINTING
   ANYTHING, THE RESISTORS WILL RECOWER ITS STRENGTH BY 20 MINUTES
 7. 電阻為發熱性零件, 所以電阻間不應相互堆積或接近其它發熱零件組合成,而防礙其散熱性。
   THE RESISTORS ARE REQUESTED NOT TO PLACE BY THE OTHER HEATING
   ACCESSORIE, WHICH WILL OBSTRUCT THEIR HEAT DISSIPATION

?
联系我们

地址:广东省东莞市长安镇上沙工业区

电话:180-0275-8998

传真:(86)0759-81889506

邮箱:dgzhangyi1688@163.com

扫一扫关注我们
Copyright ? ?2018 糖果派对连环夺宝平台? ?版权所有 粤ICP备13033718号-2